本文 首发于 🌱 煎茶转载 请注明 来源

Telnet协议是TCP/IP协议族中的一员,是Internet远程登陆服务的标准协议和主要方式。它为用户提供了在本地计算机上完成远程主机工作的能力。在终端使用者的电脑上使用telnet程序,用它连接到服务器。终端使用者可以在telnet程序中输入命令,这些命令会在服务器上运行,就像直接在服务器的控制台上输入一样。可以在本地就能控制服务器。要开始一个telnet会话,必须输入用户名和密码来登录服务器。Telnet是常用的远程控制Web服务器的方法。

环境

  • Cisco Packet Tracer 5.3
  • Windows 10

操作

操作:按照如图所示连接拓扑图
image.png
(1)配置PC IP

PC0 设置
192.168.1.2/24
PC1 设置
192.168.1.3/24

(2)配置交换机VLAN1 IP

/* part1 为vlan配置ip并开启vlan */
Switch>enable
Switch#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#interface vlan 1
Switch(config-if)#ip address 192.168.1.1 255.255.255.0
Switch(config-if)#no shutdown

%LINK-5-CHANGED: Interface Vlan1, changed state to up


%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up
Switch(config-if)#

/* Part2 查看已配置的IP */
Switch(config-if)#^Z
Switch#
%SYS-5-CONFIG_I: Configured from console by console

Switch#show running-config
...
interface Vlan1
 ip address 192.168.1.1 255.255.255.0

/*  Part3 开启Vlan */
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.	
Switch(config)#interface vlan 1
Switch(config-if)#no shutdown

/* Part4 查看Vlan状态 */
Switch(config-if)#^Z
Switch#
%SYS-5-CONFIG_I: Configured from console by console

Switch#show interfaces vlan 1
Vlan1 is up, line protocol is up
...

(3)配置交换机本地登录口令

/* Part 1 设置明文密码*/
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#enable password 123
// 注:取消密码可用no enable password

/* Part 2查看设置的密码 */
Switch(config)#^Z
Switch#
%SYS-5-CONFIG_I: Configured from console by console

Switch#show running-config
...
enable password 123
...

(4)配置交换机远程登陆及验证

Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#line vty 0
Switch(config-line)#password 123 //(Telnet密码为123)
Switch(config-line)#login local //(login是开启远程登录密码验证,login local不但要求TELNET密码,还要求提供用户名)
Switch(config-line)#

(5)添加可远程登陆交换机的用户

/* Part 1 添加用户 */
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#line vty 0
Switch(config-line)#password 123
Switch(config-line)#login local
Switch(config-line)#
Switch(config-line)#exit
Switch(config)#username admin password admin

/* Part 2 查看添加的用户 */
Switch(config)#exit
Switch#
%SYS-5-CONFIG_I: Configured from console by console

Switch#show running-config
...
username admin password 0 admin
...


(6)测试连接

// 在PC0的CMD中测试
/* Part 1 Ping交换机 */
PC>ping 192.168.1.1

Pinging 192.168.1.1 with 32 bytes of data:

Reply from 192.168.1.1: bytes=32 time=5ms TTL=255
Reply from 192.168.1.1: bytes=32 time=5ms TTL=255
Reply from 192.168.1.1: bytes=32 time=6ms TTL=255
Reply from 192.168.1.1: bytes=32 time=6ms TTL=255

Ping statistics for 192.168.1.1:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 5ms, Maximum = 6ms, Average = 5ms
    
/* Part 2 Telnet 连接交换机 */
PC>telnet 192.168.1.1
Trying 192.168.1.1 ...Open

User Access Verification

Username: admin
Password: 
Switch>

(7)配置多用户连接

// 在PC0连接的前提下,再使用PC1尝试连接
/* Part 1 PC1 Ping Switch */
PC>ping 192.168.1.1

Pinging 192.168.1.1 with 32 bytes of data:

Request timed out.
Reply from 192.168.1.1: bytes=32 time=6ms TTL=255
Reply from 192.168.1.1: bytes=32 time=6ms TTL=255
Reply from 192.168.1.1: bytes=32 time=5ms TTL=255

Ping statistics for 192.168.1.1:
    Packets: Sent = 4, Received = 3, Lost = 1 (25% loss),
Approximate round trip times in milli-seconds:
    Minimum = 5ms, Maximum = 6ms, Average = 5ms
    
/* Part 2 PC1 Telnet 连接Swithc */
PC>telnet 192.168.1.1
Trying 192.168.1.1 ...Open

[Connection to 192.168.1.1 closed by foreign host]
// 连接失败,因为交换机vty设置只能同时打开一个会话,下面设置一下,使两台PC可同时访问

/* Part 3 修改Tenlet配置 */
// 可直接在PC0直接进行
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#line vty 0 1
Switch(config-line)#password 123
Switch(config-line)#^Z

/* Part 4 重新尝试Part 2 */
PC>telnet 192.168.1.1
Trying 192.168.1.1 ...Open


User Access Verification

Password: 
Switch>
// 成功